Browse Other Categories

Bracing Shelf Support Bracket (BSB)

This bracket complies with arrangements for enhanced and super bracing included in the revised BS 5268:Part 3.

'BSB' Web Page > | 'BSB' Tech Data PDF >  |

Camplate Nailed plate Timber Fastener (CP)

Camplates are flat nail plates used to connect two timber members together. The concentric dimples pressed into the plate assist in the location of the nail. The CP is BBA approved.

Use 3.75 x 30mm square twist nails.

'CP' Web Page > | 'CP' Tech Data PDF >  |

Glide Shoe (GS)

The Glide Shoe is specially designed to allow horizontal movement between the trussed rafter and wall plate. It permits lateral movement of raised trusses up to 15mm during installation of roofing materials and resists uplift forces. Typically used on one or both ends of the truss as determined by the truss designer.

'GS' Web Page > | 'GS' Tech Data PDF >  |

Face FIx Heavy Girder Truss - SDS

HGUQ hangers are similar to the HGUS double shear hangers, however they use SDS scerws instead of nails for faster and easier installation.

The SDS screws help transfer the load between the plies of the supporting truss when they penetrate all plies.

'HGUQ' Web Page > | 'HGUQ' Tech Data PDF >  |

Hip Ridge Connector (HRC)

The HRC is a one-piece connector for supporting hip members from the ridge beam or rafters. It is site adjustable slope for right and left 45° skewed rafters

'HRC' Web Page > | 'HRC' Tech Data PDF >  |

Joist End Support (JES)

The JES is a two piece metal-work solution which enables the use of engineered timber I-Joists in loft conversions, offering a safe and economic alternative to the traditional method which involves steel girders.

'JES' Web Page > | 'JES' Tech Data PDF >  |

Light Slope and Skew Adjustable Hanger (LSSU/LSU)

With these site adjustable hangers you will always have the right hanger available for those special rush projects.

This versatile range of products attaches joists/rafters to timber supports at any slope, up or down or at any skew, left or right - up to and including 45 degrees.

'LSSU/LSU' Web Page > | 'LSSU/LSU' Tech Data PDF >  |

Mono Truss Shoe Girder Hanger (LUS/HUS/HGUS)

These joist hangers are for supporting mono trusses and girder trusses from timber members.

The feature double shear nailing which allows the distribution of the carried member's load through two points on each nail for greater strength. It also means faster installation with fewer nails.

'LUS/HUS' Web Page > | 'LUS/HUS' Tech Data PDF >  |

Truss Clip (TCP)

The TCP Truss Clip attaches girders, trusses and rafter to wall plates to provide wind restraint.

'TCP' Web Page > | 'TCP' Tech Data PDF >  |

Adjustable Truss Hanger (THA)

THA is a one piece hoist hanger for supporting trussed rafters and composite timbers from timber members. It provides great support with ease of installation, with two nailing options: either use one nail throughout (3.75x30mm) or combine with double shear nailing using a 3.75x75mm nail. Comes in seat widths 38mm to 100mm.

'THA' Web Page > | 'THA' Tech Data PDF >  |

Girder Truss Hanger

These heavy duty truss hangers are designed to support multiple ply girder trusses from vertical truss members. They can be sloped down to 30 degrees and/or skewed left or right up to 45 degrees.

'THG' Web Page > | 'THG' Tech Data PDF >  |

Tie Plate (TPA)

The TPA is a flanged nail-on plate for non-structural applications only. The holes are ready for 3.35mm width nails.

'TPA' Web Page > | 'TPA' Tech Data PDF >  |

Loft Vent Plate (VP)

The VP is part of the I-Loft system. The vent plate is a 1.2mm thick, 300mm long galvanised steel plate which provides a fast and cost effective solution to providing ventilation in the roof space.Once installed, it allows the six 20mm diameter holes to be drilled, whilst maintaining the strength of the solid sawn timber.

'VP' Web Page > | 'VP' Tech Data PDF >  |

Variable Pitch Connector (VPA)

VPA is an engineered one-piece connector for attaching I-Joist rafters to wall plates. It is adjustable to slopes between 15 and 45 degrees with a special interlock design indicating when the maximum pitch is reached.

'VPA' Web Page > | 'VPA' Tech Data PDF >  |

Valley Truss Clip (VTC2)

VTC2 is a valley truss to common truss connector.

'VTC2' Web Page > | 'VTC2' Tech Data PDF >  |