Browse Other Categories

Face Fix Heavy Girder Truss Hanger (HGUS)

The HGUS is a one piece, non-welded, joist hanger for supporting solid composite beams from timber members.Double shear nailing allows distribution of the carried member’s load through two points on each nail for greater strength.

'HGUS' Web Page > | 'HGUS' Tech Data PDF >  |

Heavy I-Joist Hanger (HITB)

The HITB is a heavy duty version of the ITB, an innovative new hanger that eliminates the requirement for backer blocks when supported from an I-joist header.The bottom flange location tabs and an open top flange provide enhanced capacity and improved ease of installation.

'HITB' Web Page > | 'HITB' Tech Data PDF >  |

Heavy Metal Web Joist Hanger (HIUB)

The IUB hanger supports metal web joists and solid timber joists without the need for plywood gussets. It incorporates the unique features of bottom flanges, which provide enhanced capacity and can be used on metal web joists or solid joist headers.

Bottom flanges provide enhanced download capacity and quickly sets the hanger onto the header. Obround holes in face to provide easier nailing access in tight locations.

'HIUB' Web Page > | 'HIUB' Tech Data PDF >  |

Heavy Duty Face Fix Hanger (HU/U)

These are veavy-duty hangers designed for applications requiring additional strength. The composite HU hangers have round and triangle holes in the face and joist. The hanger depth is to be at least 60% of the carried member depth to prevent rotation, unless additional lateral restraint is added to the top of the carried member.

'HU/U' Web Page > | 'HU/U' Tech Data PDF >  |

I-Joist Hanger (ITB)

The ITB is an innovative new hanger that eliminates the requirement for backer blocks when supported from an I-joist header.The bottom flange location tabs and an open top flange provide enhanced capacity and improved ease of installation.

'ITB' Web Page > | 'ITB' Tech Data PDF >  |

Backer Free I-Joist Hanger with Adjustable Skew (ITBS)

The revolutionary ITBS reduces build cost, confusion, speed of installation and stock holding.

The ITBS solves the problem of skew hangers in timber to timber connections. It can be handed left or right on site by the carpenter, removing confusion when the floor is built opposite to the drawing. The ITBS is also fully adjustable from 5° to 67.5° skew, reducing the need for ‘special’ skew hangers. Finally, the ITBS is a Backer Free hanger removing the need for Backer Blocks in standard installation.

'ITBS' Web Page > | 'ITBS' Tech Data PDF >  |

Top Flange I-Joist Hanger (ITSE/MIT)

The ITSE is a one piece, non welded hanger, top fix hanger for supporting I-joists from timber members. Mit hangers are a one-piece, non-welded joist hanger for supporting I-joists and structural composite timber from timber members.

This new hanger incorporates the “Strong Grip™ which secures the I-Joist without the need for any fasteners - where no uplift is required.

'ITSE/MIT' Web Page > | 'ITSE/MIT' Tech Data PDF >  |

Metal Web Joist Hanger (IUB)

The IUB hanger supports metal web joists and solid timber joists without the need for plywood gussets. It incorporates the unique features of bottom flanges, which provide enhanced capacity and can be used on metal web joists or solid joist headers.

Bottom flanges provide enhanced download capacity and quickly sets the hanger onto the header. Obround holes in face to provide easier nailing access in tight locations.

'IUB' Web Page > | 'IUB' Tech Data PDF >  |

Metal Web Joist Hanger with Adjustable Skew (IUBS)

The IUBS solves the problem of skew hangers in timber to timber connections. It can be handed left or right on site by the carpenter, removing confusion when the floor is built opposite to the drawing.

The IUBS is also fully adjustable from 5° to 67.5° degrees skew, reducing the need for “special” skew hangers.

'IUBS' Web Page > | 'IUBS' Tech Data PDF >  |

Face Fix Hanger for SIP Panels

The IUQ/HIUQ is the first hanger range specifically designed to allow engineered joists to be face fixed to a structural insulated panel (SIP), when used in conjunction with the Simpson Strong-Tie patented SDS Screws.

'IUQ' Web Page > | 'IUQ' Tech Data PDF >  |

Face Fix I-Joist Hanger (IUSE)

The IUSE is a one piece, non welded face fix hanger for supporting I-Joists from timber members. This new hanger incorporates the "Strong Grip" which secures the I-Joist without the need for amy fasteners - where no uplift is required.

'IUSE' Web Page > | 'IUSE' Tech Data PDF >  |

I-Joist & Structural Composite Top Flange Hanger

LBV and BI hangers are a one-piece, non-welded joist hanger for supporting i-joists and structural composite timber from timber members. This design configuration has the material section where it counts, resulting in maximum load values. The LBV is designed especially for use with multiple ply headers of 38mm or 45mm thick.

'LBV/BI' Web Page > | 'LBV/BI' Tech Data PDF >  |

Mini Hanger for I-Joist (MH)

The MH is a one-piece hanger for light duty applications such as trimmers and ceiling joists of rectangular section. The seat tab ensure easy and accurate placement with an easy bend when not required. Fully tested on a range of solid headers.

For I-Joist headers, fill all round holes with nails.. The hanger depth should be at least 60% of the carried member depth to prevent rotation, if less than 60% additionaladditional lateral restraint is required to the top of the carried member.

'MH' Web Page > | 'MH' Tech Data PDF >  |

Face Fix I-Joist Hanger (MIU/HIU)

MIU and HIU hangers are a one piece, non-welded, face mounted hanger for supporting i-joists from timber members. The MIU and HIU hangers feature Positive Angle Nailing (PAN), which minimises splitting of the flanges while permitting time-saving nailing from a better angle. With PAN nailing, the slotted hole material is not removed, but is used to channel and confine the path of the nail to the optimum angle.

Joist top flanges are laterally restrained by the side of the hanger, eliminating the need for web stiffeners. I-joist manufacturers may require web stiffeners.

'MIU/HIU' Web Page > | 'MIU/HIU' Tech Data PDF >  |

Multiple Joist Connector (MJC)

The Multi Joist Connector (MJC) allows two i-joists or two open-web joists to be fixed together to act as a single unit, transferring the incoming load from the loaded ply to the unloaded ply.

The MJC is an improved solution to the traditional filler block detail, which historically has been time consuming to fit and difficult to check if fitted or if fitted correctly.

It’s simple and effective design allows one size of product to be used on any joist size – regardless of height or width.

'MJC' Web Page > | 'MJC' Tech Data PDF >  |

Metal Web Joist Screws (SDS)

Simpson Strong-Drive Screws can be used for a fast and effective connection of the timber flanges of a 2-ply open web floor joist. Simpson Strong-Drive� Screws are in 2 styles, SDS25 series and SDS6, dependent on the length as shown below. SDS25 series features a 3/8 hex head (driver supplied). SDS6 features a T30 T star head (driver supplied).

'SDS' Web Page > | 'SDS' Tech Data PDF >  |

Skewed 45 Degree Hanger (SUR/L and HSUR/L)

The SUR, SUL, HSUR and HSUL are a one piece, non-welded, joist hanger for supporting skewed timber joists from timber members.
The SUR, SUL, HSUR and HSUL provide tested and standardised 45° skewed hangers.
MATERIAL: SUR and SUL: 1.5mm; HSUR and HSUL: 2.0mm pre-galvanised mild steel.

'SUR/L and HSUR/L' Web Page > | 'SUR/L and HSUR/L' Tech Data PDF >  |

Adjustable Strap Hanger (THAI)

THAI are a one piece, non-welded, joist hanger for Supporting composite timbers from timber members. The model number and size is stamped onto the seat of most sizes for easy identification of the hanger, even after installatio

'THAI' Web Page > | 'THAI' Tech Data PDF >  |

For I-Joist and Structural Composite Timber (WPU/GLTV)

These are a welded joist hanger for supporting i-joists and structural composite timber from timber members. They offer the greatest design flexibility and versatility.

GLTV hangers are designed for use with structural composite lumber headers and may take heavy loads. The top flange nails are sized and specifically located to prevent degradation of the header due to splitting of laminations.

'WPU/GLTV' Web Page > | 'WPU/GLTV' Tech Data PDF >  |

Slotted Z-Clip (ZS)

The ZS clip allows I-joists or solid sawn timber to be used as noggings between joists to support floor decks or partitions.

'ZS' Web Page > | 'ZS' Tech Data PDF >  |